Newly installed Thermann 26R gas continuous flow hot water system by Woolf Plumbing.

Hot Water

  • ★ 4.8 from 714 Google reviews
  • Fully insured

Call us when your hot water has stopped, a unit is leaking or it's time for a new one. We replace and repair hot water systems, from gas units to heat pumps.

Ashley's team at Woolf Plumbing & Gas works out of Forrestdale and covers Perth from Alkimos to Dawesville. You can reach us on (08) 6555 7757 or through the quote form. Tell us what the unit is doing and whether it runs on gas or electricity.

A new unit is more than a swap. WA has a rule on temperature control that applies when a water heater is replaced, and gas units come under the gas rules. Both are covered below. So are the repairs we've made and the replacements we've done lately.

Repair or replace? Describe what the unit is doing and we'll set out the options in plain words.

Which hot water systems do we replace?

The systems we've replaced are gas storage, gas continuous-flow, heat pump and electric storage. We've also taken old roof-mounted solar systems off and put gas units in their place. Each type appears in the jobs further down.

Can a hot water system be repaired?

Sometimes. One part can be the fault. Then the fix is a new part. On a gas storage unit in Baldivis in April 2025 we replaced the gas control valve and took out the burner assembly. On another Baldivis job in June 2025 we removed a clogged inlet strainer and replaced a corroded inlet fitting and a cold water valve. In Bassendean in July 2025 the part was a thermocouple. In Duncraig in June 2026 we drained and flushed a unit.

Rust is another matter. The Willetton job below was a replacement, and the old unit's base and combustion chamber had rusted and corroded. Whether a repair is worth it on your unit depends on the fault.

What does the WA temperature rule mean for a replacement?

WA Government says "temperature control devices must be fitted when replacing a water heater". The rule has applied since 1 May 2024, to existing installations used for personal hygiene. Industry Bulletin 161, from Building and Energy, puts it this way: the requirement "will apply when a water heater is replaced, relocated, or added".

Building and Energy's technical note on water heater installations covers the pipework around the unit. Drain lines from relief valves must fall continuously, carry no tap or valve and end at an approved point of discharge. An instantaneous unit needs an accessible isolation valve next to the heater, outside its casing. The Plumbers Licensing and Plumbing Standards Regulations 2000 add that water heaters must be installed to the manufacturers' specifications.

Gas units are gas work too. In WA, a gas appliance counts as part of a gas installation, and work on an installation is gasfitting work. The Gas Standards (Gasfitting and Consumer Gas Installations) Regulations 1999 say an installation must pass a pressure test and be gas-tight before it is commissioned. PL 9348 is our plumbing contractor licence, and GF 14901 is our gas fitting licence.

How we replace a unit

Here's the order of work.

  1. The old unit is drained and taken out. The new one stands in the same spot, or on a new base or slab.
  2. New copper pipework goes in, lagged, with isolation valves.
  3. Temperature control goes in to meet the WA rule, such as the tempering valve at the unit on the Como job below.
  4. The pressure and temperature relief valve gets a drain line run to an approved point of discharge.
  5. On a gas unit the gas supply gets a copper line and an isolation valve. Then a digital manometer goes on the gas, at the meter and at the unit, and the valves are sprayed to check for leaks.
  6. We've checked the hot water at a tap with a probe thermometer. We've also stuck shutdown instructions on a new unit, with our phone number on them.

Recent hot water jobs

Willetton, March 2026. Rust had set into the combustion chamber and base of the old gas storage unit. We removed it and stood a new gas storage system on a slab against the brick wall. The relief valve got a copper drain line.

Rockingham, June 2026. The old roof-mounted solar system came off. In its place a natural gas continuous-flow unit went onto a brick wall, with new copper gas pipe and an isolation valve. The gas was then pressure tested on a digital manometer.

High Wycombe, August 2026. A split heat pump system was installed outside a brick home. The heat pump unit stands beside its storage tank, and the pipework is lagged.

Duncraig, August 2026. The new unit is natural gas storage. It sits on a concrete base, with a limestone block wall at its back. Its hot and cold pipes are lagged, a copper gas line with isolation valves feeds it, and a drain runs to a gully.

Como, September 2026. The new unit was a mains-pressure electric storage system. It came with a tempering valve, copper pipework and a pressure and temperature relief valve, also piped in copper.

Where we do it

Our recent hot water jobs span the Perth hills, Rockingham and Peel and both sides of the river: South of the river and North of the river.

Related services

If a unit is leaking badly, our Emergency Plumber line is 24/7. When the leak is in the pipes and not the unit, Leak Detection is the page to read. A gas unit also brings in Gas Plumbing, which sets out the rules for gas work and how we test it.

Frequently asked questions

How much does a new hot water system cost?

That depends on the job, so we don't print a figure here. Ring or use the quote form and you'll get a quote, with the details discussed before work starts.

Can my hot water system be repaired instead of replaced?

Sometimes, yes. On storage units we've replaced a gas control valve, a cold water valve, a corroded inlet fitting and a thermocouple, and removed a clogged inlet strainer. Whether a repair makes sense on yours depends on the fault.

What do the WA rules require when a water heater is replaced?

WA Government says temperature control devices must be fitted when replacing a water heater. That has applied since 1 May 2024, to existing installations used for personal hygiene. Industry Bulletin 161, from Building and Energy, says the same requirement applies when a heater is replaced, relocated or added.

Why does a gas hot water unit need a gas fitter?

Because WA treats a gas appliance as part of a gas installation, and work on an installation is gasfitting work. The Gas Standards Act 1972 makes it an offence to do prescribed gasfitting work with no authority.

Which types of hot water system do you replace?

We've replaced gas storage, gas continuous-flow, heat pump and electric storage units. Old roof-mounted solar systems have also come off, with gas units going on in their place.

Ready to get started?

(08) 6555 7757Book a free quote

Contact Woolf Plumbing & Gas

Call us, or send the form and we call you back.

Book Your Free Quote Now

We come out and quote for free, with no call-out fee. Tell us about the job and we call you back.

We use your details only to reply to your enquiry. Privacy policy

OR Call (08) 6555 7757

Call (08) 6555 7757Book a free quote